Sewing Machine Not Catching The Bobbin Thread – Causes and Solutions

The bobbin thread is an essential part of your sewing machine. It holds the material, which makes it possible for you to sew. The bobbin thread should be able to catch on the needle plate without any problems and should not get stuck in between it or anywhere else in your machine. If this happens with your machine, there must be something wrong with its mechanism or parts.

Key Takeaways

• Poor threading is the leading cause of the sewing machine not catching the bobbin thread.
• The bobbin is not inserted correctly.
• The bobbins or the bobbin case are damaged.
• There’s dirt and lint under the needle plate cover.

If you are experiencing this problem, try removing upper and lower tension on your machine if possible; then check everything else listed here one by one until you find a solution that works for you!

The Main Cause is Poor Threading.

The leading cause of this problem is poor threading. When you change your bobbin, the thread should be wound on it so that it doesn’t fall off when you remove it from its case.

If your machine doesn’t catch the new bobbin correctly, then there may be too much slack in your stitch, and you may have to start over again. If you find that this happens often, check how tightly each part fits together before sewing again (and make sure nothing has been knocked loose).

You can also try using different needles or things like pins or string if they seem to work better than regular needles with varying fabric materials.

The Bobbin is Not Inserted Correctly.

Another possible cause of a bobbin not catching the thread is that you’re not inserting it correctly. If you’re having problems with this, check to see if your bobbin case is in place and also make sure there are no tears or cracks in your sewing machine’s case.

The Bobbins or The Bobbin Case are Damaged.

The first thing to check is that the bobbin or the bobbin case is not damaged. If you have a metal-bobbin sewing machine, you can also try using another one. If it works, then there is no other problem with your machine, and if it doesn’t work, there might be something wrong with the threading system of your hand-sewing machine.

There’s Dirt and Lint Under the Needle Plate Cover.

If you have a machine with a needle plate cover, it may be caked with lint and debris. The best way to remove this material is with a lint brush or compressed air. You can also use an old toothbrush or Q-tip to clean the area where the needle plate sits on your sewing machine’s body. Once you’ve cleaned out as much dirt as possible, replace your needle plate cover and try again!

The Upper or Lower Tension is Incorrect.

The upper tension is too tight. A few things can cause this, but it most likely means your bobbin thread is not catching the fabric correctly when you start sewing.

If this is the case, try loosening up on your upper setting and see if that helps. If that doesn’t work, try loosening up both sets until you find one that works.

The lower tension is too loose. Many reasons could cause this: maybe you have too much space between each stitch; maybe your machine has been sitting unused for a while (this will make it harder to get started), or maybe there’s something wrong with your device itself; perhaps it needs new needles!

There’s Too Much Upper Thread in the Take-up Lever.

It would be best to ensure that the upper thread is not too long. The take-up lever should be fully raised, and the right amount of tension applied to the upper tension screw on your machine. If you are having trouble getting this right, there are a few things to try:

• Ensure that your sewing machine has enough room for an extra foot or two of thread between each bobbin and its corresponding needle plate (see image below). This can help catch all types of threads coming out from their bobbins.
• Try using some elastic cord halfway through each bobbin so that when it comes out from under pressure, it doesn’t get tangled up with other pieces nearby; this may also help prevent this problem from occurring!

How to Solve Bobbin Thread Not Catching Issue?

The bobbin thread not catching issue can be solved by checking the following points:

• Check that the bobbin is inserted correctly. Check if it is straight. Also, ensure that there are no obstructions on either side of your machine’s bobbin case, as they could cause a problem while sewing.
• Check that you have appropriately wound your machine’s upper thread onto its spool, which will help ensure proper tension during the operation of your machine. If you are using multiple lines on one spool, ensure they all wind correctly through their respective guides so as not to cause any problems with feeding or tensioning during use!
• Inspect both upper and lower threads for tangled knots or frays before sewing begins – this often happens when people don’t know what they’re doing; remember: always check ahead before starting up!

Conclusion

We hope this article has helped you solve your bobbin thread not catching issue. If you have any questions, don’t hesitate to contact us, and we will get back to you as soon as possible!